Check out PSI Conversion for your LS/LT swap!
https://www.psiconversion.com/

All wires used for battery relocation were purchased from Wirebarn:
https://www.wirebarn.com/

Thirdgen wiring diagrams:
http://www.austinthirdgen.org/?pid=19

Thirdgen support:
https://www.thirdgen.org/

Grab an LsxMatt hat here:
https://lsxmatt.com/collections/all

Parts and tools: (In order of appearance)

Brake pedal bushings:
https://amzn.to/2WiBHEH

Rust reformer:
https://www.lowes.com/pd/Rust-Oleum-S...

Krylon Fusion satin black:
https://amzn.to/3yh4GG4

Electrical connector spray:
https://amzn.to/3DbwTl5

Turn signal switch:
https://amzn.to/3BaGIOB

Hazard switch button:
https://www.ebay.com/itm/272446413974

Wiper/cruise control stalk:
https://amzn.to/2XP8iCy

Steering wheel puller:
https://amzn.to/2WmtK18

Steering wheel lock plate remover:
https://amzn.to/3gsntIl

C6 Corvette DBW gas pedal:
https://www.psiconversion.com/product...

BMR battery relocation tray:
https://www.bmrsuspension.com/?page=p...

Much cheaper battery tray alternative:
https://www.summitracing.com/parts/af...

Hydraulic crimping tool:
https://www.harborfreight.com/hydraul...

Firewall battery cable bulkhead:
https://amzn.to/3y93gx5

0 gauge crimp terminals (with heatshrink):
https://amzn.to/3jbtHOq

Zip tie sticky back wire hold downs:
https://amzn.to/3B37uZ0

Side terminal battery studs:
https://amzn.to/3gqIcvT

Assorted heatshrink tubing:
https://www.harborfreight.com/42-piec...

Postive wire busbar:
https://amzn.to/3zeuJPf

Wire loom:
1/4" -- https://www.harborfreight.com/1-4-qua...
3/8" -- https://www.harborfreight.com/3-8-eig...
1/2" -- https://www.harborfreight.com/1-2-hal...

Butane torch:
https://amzn.to/3j9USsX

Self tapping drill screws:
https://amzn.to/3goagA0

2 inch hole saw bit:
https://amzn.to/2Wh3xBf

Step drill bit:
https://amzn.to/3B87y9J

Speaker wire:
https://amzn.to/3Db0laY

LT GEN V ONLY Oil adapter:
https://www.ictbillet.com/lt-gen-v/lt...

LS Oil adapter (uses cooler port on side of pan):
https://www.ictbillet.com/ls-ls1-1-8-...

LT GEN V AND LS coolant sensor block adapter:
https://www.ictbillet.com/lt-m28-to-3...

Cable driven speedometer conversion box (uses gps signal to spin cable):
https://www.jegs.com/i/JEGS/555/41800...

Dakota digital speedometer/tach calibration box (goes inline with speed and tach wires to make gauges read accurately):
https://www.summitracing.com/parts/da...

GEN V LT SWAP ONLY Canbus dongle for speed and tach output:
https://www.psiconversion.com/product...

OBD port splitter:
https://www.psiconversion.com/product...

Chapters:

0:00 Welcome back
1:34 Brake pedal rebuild
4:00 Steering column rebuild
10:55 I got carried away again
12:30 Mullet magic
12:58 Drive by wire gas pedal install
16:03 Fuel injection wiring harness
17:15 PSI Conversion, Cost/Goals
19:09 Battery relocation
23:46 Engine harness walkthrough
25:36 Swappers NEED to know this
30:02 Engine harness install
30:28 Mullet magic 2
31:16 Two fuel pumps
37:24 Tapping into the 80's harness
40:20 Mullet Matt, GAUGE WIRING
42:48 More gauge wiring, and wiring, and wiring, and WIRING..
49:27 We're done here
50:54 I forgot