If you've been looking for detailed instructions on how to wire your Bigtreetech SKR V1.4 Turbo, this is the video for you! I'll walk you through the wiring diagram and show how I installed this board in my Ender 5 Plus 3D printer.

#ender5plus #bigtreetech #marlin

Full Playlist of Bigtreetech Mods:    • Bigtreetech Upgrades  

Links to possible "I want to keep the stock display" solutions:
https://github.com/exetico/Marlin/blo...
https://www.deviousweb.com/2020/05/08...

Product Links:
Please note that Amazon occasionally changes their listings. Please verify the product is correct before ordering.

Note: All of the following links have been replaced by the SKR 2 by Bigtreetech. It appears that the SKR V1.4 Turbo is no longer available.
Bigtreetech SKR V1.4 Turbo (Board-Only): https://amzn.to/2VH3afW
Bigtreetech SKR V1.4 Turbo (with 4 x TMC2208): https://amzn.to/2Brul7B
Bigtreetech SKR V1.4 Turbo (with 5 x TMC2209): https://amzn.to/2D2iwox

Bigtreetech TFT35 V3.0 (text and touchscreen) for either board: https://amzn.to/3isVp76 OR https://amzn.to/30VXdNR

Buy direct from Bigtreetech: https://www.biqu.equipment/

USB Type B Male to Female Extension Cable (90 Degree Left Angle): https://amzn.to/30fgcm5
Here's the 90 Degree Right Angle version if the other is out of stock or if this just works better for your setup: https://amzn.to/2DTdRFV
Pick One:
MicroSD to MicroSD Extension Cable: https://amzn.to/2Zxwo2U
OR:
MicroSD to Regular SD Extension Cable: https://amzn.to/3ezXPNZ

M3 Screw Assortment: https://amzn.to/38ZJHfQ

Documentation:
Manual: https://github.com/bigtreetech/BIGTRE...
Board Layout: https://github.com/bigtreetech/BIGTRE...

Shared Files:
Latest Marlin 2.0.7.2 Files:
Shared Z-stepper Source: https://github.com/KerseyFabrications...
Pre-built for TMC2208: https://drive.google.com/file/d/1U0lQ...
Pre-built forTMC2209: https://drive.google.com/file/d/1kH0V...

Dual Z-Steppers Source: https://github.com/KerseyFabrications...
Pre-built for TMC2208: https://drive.google.com/file/d/1Oxai...
Pre-built for TMC2209: https://drive.google.com/file/d/1r_XY...

--------------------------------------------------------------------------------------------------------------------------------

How-to Flash:
1. Just copy the correct .bin file to the microSD card and rename it firmware.bin.
2. Power cycle the machine.
3. When it boots back up it should flash the firmware.
4. The splash screen should now say 2.0.6 as the version. If you look at the microSD card contents it will have a firmware.CUR and not a firmware.bin.

SUCCESS!


3D Files:
Ender 5 Plus Board Mount, Center Mounted Board (As shown in this video.): https://www.thingiverse.com/thing:454...

Ender 5 Plus Board Mount, Edge Mounted Board: https://www.thingiverse.com/thing:405...


Other Files:
Link to Bigtreetech GitHub: https://github.com/bigtreetech/BIGTRE...

-------------------------------------------------------------------------------------------------------------------------

For Amazon Links: As an Amazon Associate I earn from qualifying purchases.
Other purchase links may also be affiliate links.

You can support my work monthly on Patreon:
  / kerseyfabrications  

You can support my work via one-time PayPal donations:
https://www.paypal.me/kerseyfabs

Where to find me on Social Media:
Facebook:   / kerseyfabs  
Instagram:   / kerseyfabs  
Twitter:   / kerseyfabs  

Contact: [email protected]

Credits:
Opening Music:
––––––––––––––––––––––––––––––
Happy by MBB   / mbbofficial  
Creative Commons - Attribution-ShareAlike 3.0 Unported - CC BY-SA 3.0
Free Download / Stream: https://bit.ly/Happy-MBB
Music promoted by Audio Library    • Happy – MBB (No Copyright Music)  
––––––––––––––––––––––––––––––

"Subscribe Button" Graphic by MrNumber112    • Free Download: Subscribe Button + Not...