This step-by-step DIY installation of the TTE710 hybrid turbo will show you how I transformed my 2018 Audi B9 S4 into an absolute monster. If you're considering a hybrid turbo, especially The Turbo Engineers TTE810 or 710, you should check out 034Motorsport's Dynamic+ Stage 3 ECU/TCU tuning. The power output and drivability of the car is absolutely fantastic, switch to E85 and it's a rocket ship. I will also show you an upper and lower PCV hose service. The lower PCV hose does require removal of the turbo, so this is an opportune time to swap it out. You will likely need other supporting mods to install this turbo, make a plan with your tuner!

TTE 710 Turbo - https://bit.ly/tte710turbo
TTE 810 Turbo - https://bit.ly/tte810turbo
TTE 4-Bar MAP Sensors - https://bit.ly/4barmapforb9

034 B9/B9.5 Dynamic+ Tuning - https://bit.ly/034DynamicEA839
034 SuperDuper Inlet - https://bit.ly/superduberb9

Funk B9 Turbo Blanket - https://bit.ly/funkb9blanket
Liqui Moly Pro-Line Additive - https://bit.ly/prolineadditive
Turbo Manifold Clamp 059253139D - https://bit.ly/b9turboclamp
Turbo to Manifold Gasket 059253232C - https://bit.ly/b9turboclampgskt
Manifold Exhaust Gasket 06M253039G (2x) - https://bit.ly/b9turbomanigskt
Turbo to Catalyst Gasket 8W0253115G - https://bit.ly/b9turbocatgskt
M6x18 Torx Bolt N10196103 (4x) - https://bit.ly/m6x18
M6x12 Torx Bolt N10335206 (4x) - https://bit.ly/m6x12
Turbo Line Green O-Ring WHT007689 (3x) - https://bit.ly/b9turbooring
Lower PCV Hose 06M103217DD - https://bit.ly/b9pcvhose1
Upper PCV Hose 06M129041 - https://bit.ly/b9pcvhose2
Thermo-Tec 3' Heat Shield - https://amzn.to/3MQF6lF

Capri Tools Stubby Triple Square Bits - https://amzn.to/3E2OL3N
GEARWRENCH Half Moon Wrench Set - https://amzn.to/42cvpCE
Sunex 9726 Mini Ratchet & Bits - https://amzn.to/3m1V5CX
VIM Tools Half-Cut Torx Bits - https://amzn.to/3MvbQ2j
AEJ Metric Hex/Allen Bit Set - https://amzn.to/3MgIC8P
Low Profile Offset Torx Drivers - https://amzn.to/4159bSR
TEKTON 3/8" x 7/8" Offset O2 Socket - https://amzn.to/3MHkwV8
TEKTON Angled Tip Pry Bars - https://amzn.to/43x0na8

As an Amazon Associate and ECS Tuning Affiliate I earn from qualifying purchases. You don't have to purchase the specific items I'm linking to in order to help the channel at no added cost to you!

00:00 Introduction
00:14 Intake Air Box Removal
01:00 Turbo O2 Sensor Removal
01:31 Turbo V-Band Removal
01:45 Loosen Wiring Harnesses
01:58 Upper PCV Hose Removal
02:29 Turbo Inlet Removal
02:46 Unplugging Lower PCV Hose From Turbo
03:06 Support DG
03:27 Disconnect Charge Pipe From Turbo Outlet
03:55 Disconnecting Turbo Oil & Coolant Lines
04:29 Wastegate Actuator Removal
04:47 Vaccum Line & Diverter Valve Disconnect
05:09 Stock Turbo Removal
06:31 Lower PCV Hose Replacement
07:15 Prepping The TTE 710 Turbo
08:53 4-Bar MAP Sensor Installation
09:51 Turbo Line O-Ring Replacement
10:15 TTE 710 Turbo Installation
11:45 Turbo V-Band Installation
12:28 Final Turbo Reassembly
13:32 Charge Pipe Turbo Outlet Connection
13:58 034 SuperDuper Inlet Installation
14:32 Lower PCV Hose to Inlet Connection
15:13 Upper PCV Hose Installation
15:22 Intake Air Box Installation
15:42 First Start & Drive TTE 710 Turbo
16:23 Final Thoughts

#theturboengineers #tte710 #034motorsport #hybridturbo #turbo